Overview
| PIN | |||
| 1 | Output 1 | V+ | positive output for voltage ranges channel 1 |
| 2 | Output 2 | V+ | positive output for voltage ranges channel 2 |
| 3 | Output 1 | I+ | positive output for current ranges channel 1 |
| 4 | Output 2 | I+ | positive output for current ranges channel 2 |
| 5 | Output 1 | – | shared ground of output channels 1 und 2 (voltage and current) |
| 6 | Output 2 | – | shared ground of output channels 1 und 2 (voltage and current) |
| 7 | Output 1 | – | shared ground of output channels 1 und 2 (voltage and current) |
| 8 | Output 2 | – | shared ground of output channels 1 und 2 (voltage and current) |
| 9 | RTD 2 | white | negative measuring current for 3- & 4-wire; for 2-wire jumper to pin 18 |
| 10 | RTD 1 | white | negative measuring current for 3- & 4-wire; for 2-wire jumper to pin 12 |
| 11 | Input 4 | – | negative input for current or voltage measurement channel 4 |
| 12 | RTD 1 | white | negative measuring input, 2-, 3- and 4-wire, Channel 1 |
| 13 | Input 4 | * | Â a jumper must be installed from here to pin 15 for current measurements |
| 14 | RTD 1 | red | positive input, 2-, 3- and 4-wire, Channel 1 |
| 15 | Input 4 | + | positive input for current or voltage measurement channel 4 |
| 16 | RTD 1 | red | positive measuring current, only for 4-wire, channel 1 |
| 17 | Input 3 | – | negative input for current or voltage measurement channel 3 |
| 18 | RTD 2 | white | negative measuring input, 2-, 3- and 4-wire, channel 2 |
| 19 | Input 3 | * | a jumper must be installed from here to pin 21 for current measurements |
| 20 | RTD 2 | red | positive input, 2-, 3- and 4-wire, channel 2 |
| 21 | Input 3 | + | positive input for current or voltage measurement channel 3 |
| 22 | RTD 2 | red | positive measuring current, only for 4-wire, channel 2 |
| 23 | Input 2 | – | negative input for current or voltage measurement channel 2 |
| 24 | Input 1 | – | negative input for current or voltage measurement channel 1 |
| 25 | Input 2 | * | a jumper must be installed from here to pin 27 for current measurements |
| 26 | Input 1 | * | a jumper must be installed from here to pin 28 for current measurements |
| 27 | Input 2 | + | positive input for current or voltage measurement channel 2 |
| 28 | Input 1 | + | positive input for current or voltage measurement channel 1 |
Overview of interfaces
Outputs
PLEASE NOTE
Current and voltage outputs can only be selected alternatively for one output channel (either only the V or only the I output of one channel is active, depending on the configuration in PiCtory)!
| Output 1 | |
| PIN | |
| 1 | V+Â Â Â positive output for voltage ranges channel 1 |
| 3 | I+Â Â Â positive output for current ranges channel 1 |
| 5 | –Â Â Â Â shared ground of output channels 1 und 2 (voltage and current) |
| 7 | –Â Â Â shared ground of output channels 1 und 2 (voltage and current) |
| Output 2 | |
| PIN | |
| 2 | V+Â Â Â positive output for voltage ranges channel 2 |
| 4 | I+Â Â Â positive output for current ranges channel 2 |
| 6 | –Â Â Â Â shared ground of output channels 1 und 2 (voltage and current) |
| 8 | –Â Â Â Â shared ground of output channels 1 und 2 (voltage and current) |
Inputs
| Input 1 | |
| PIN | |
| 24 | –Â Â Â negative input for current or voltage measurement channel 1 |
| 26 | *Â Â a jumper must be installed from here to + for current measurements |
| 28 | +Â Â positive input for current or voltage measurement channel 1 |
| Input 2 | |
| PIN | |
| 23 | –Â Â Â negative input for current or voltage measurement channel 2 |
| 25 | *Â Â a jumper must be installed from here to + for current measurements |
| 27 | +Â Â positive input for current or voltage measurement channel 2 |
| Input 3 | |
| PIN | |
| 17 | –Â Â Â negative input for current or voltage measurement channel 3 |
| 19 | *Â Â a jumper must be installed from here to + for current measurements |
| 21 | +Â Â positive input for current or voltage measurement channel 3 |
| Input 4 | |
| PIN | |
| 11 | –Â Â Â negative input for current or voltage measurement channel 4 |
| 13 | *Â Â a jumper must be installed from here to + for current measurements |
| 15 | +Â Â positive input for current or voltage measurement channel 4 |
 RTD channels
| RTD1 | |
| PIN | |
| 10 | RTD connection white (negative measuring current for 3- & 4-wire; for 2-wire jumper to pin 12) |
| 12 | RTD connection white (negative measuring input, 2-, 3- and 4-wire) channel 1 |
| 14 | RTD connection red (positive measuring current, 2-, 3- and 4-wire) channel 1 |
| 16 | RTD connection red (positive measuring current, only 4-wire) channel 1 |
Â
| RTD2 | |
| PIN | |
| 9 | RTD connection white (negative measuring current for 3- & 4-wire; for 2-wire jumper to pin 18) |
| 18 | RTD connection white (negative measuring input, 2-, 3- and 4-wire) channel 2 |
| 20 | RTD connection red (positive measuring current, 2-, 3- and 4-wire) channel 2 |
| 22 | RTD connection red (positive measuring current, only 4-wire) channel 2 |