power led of DO module keeps flashing red

Topics about the Hardware of Revolution Pi
Post Reply
sandwave123
Posts: 4
Joined: 31 May 2023, 12:49
Answers: 0

power led of DO module keeps flashing red

Post by sandwave123 »

I am currently working on creating a tool issuance system. This consists of 20 lockers whose doors are controlled by solenoids. The solenoids are controlled using 3 DO modules and 1 RevPi CONNECT SE. This system is fed with a voltage of 24V and 10 A. But as soon as I start up the system, only the RevPi works and the power LED lights up green, and at the DO all 3 flash red at the power LED. I have configured the system several times in piCtory but it just does not get connected to the DO modules. Because when I run piTest -d it doesn't see any devices.

What should I do now?
giuseppe
KUNBUS
Posts: 91
Joined: 09 Mar 2022, 13:08
Answers: 0

Re: power led of DO module keeps flashing red

Post by giuseppe »

Hallo sandwave123,

can you take a picture of your system, that I can see the wiring?

Meanwhile you can check following documentestion for your problem, maybe this could help you.
RevolutionPi IO-Modules FAQ | How to wire the RevolutionPi AIO, MIO, DIO, DI, DO modules?
Commissioning RevPi DIO High-Side Mode

Best regards
Giuseppe Pagano
sandwave123
Posts: 4
Joined: 31 May 2023, 12:49
Answers: 0

Re: power led of DO module keeps flashing red

Post by sandwave123 »

Here is a picture of the modules how they are connected
Attachments
foto wirering
foto wirering
20230602_112730 (2).jpg (224.32 KiB) Viewed 3140 times
giuseppe
KUNBUS
Posts: 91
Joined: 09 Mar 2022, 13:08
Answers: 0

Re: power led of DO module keeps flashing red

Post by giuseppe »

Hello sandwave123,

thank you for the prompt reply.
The wiring seems to be OK, and I assume that the PiBridges are connected correctly at the top.

Didn't the two links from earlier help?
if not, follow the checklist below.
Revolution Pi Checklist

Best regards
Giuseppe Pagano
sandwave123
Posts: 4
Joined: 31 May 2023, 12:49
Answers: 0

Re: power led of DO module keeps flashing red

Post by sandwave123 »

I have tried averything and they still won't turn work. So what is the best next option to do?
giuseppe
KUNBUS
Posts: 91
Joined: 09 Mar 2022, 13:08
Answers: 0

Re: power led of DO module keeps flashing red

Post by giuseppe »

type this into the console:

Code: Select all

piTest -d
and paste the output here in the chat.

and send me a screenshot of your PiCtory configuration.
JeffreyA
Posts: 2
Joined: 13 Jul 2023, 10:49
Answers: 0

Re: power led of DO module keeps flashing red

Post by JeffreyA »

Good day,

Recently, my assistance was requested to help sandwave123 with the problem of flashing lights on the DO modules. We work at the same facility.
Since the last message in this thread, a new image has been flashed onto the revpi Connect SE, in an attempt to fix the issue.
We however, still can't access the DO modules.

The result of "piTest -d" is the following "Cannot retrieve device list: No such device"
This is the result both with and without the three DO modules connected to the core module.

I've done some looking around on the forum, and this should at the very least be reporting the core module itself, if I'm not mistaken.
this post (viewtopic.php?t=3517) seemed similar to our problem, seeing as we are also facing trouble with connecting to a network.
The conclusion on our end is different however. But let me post the result of the commands below anyway. Perhaps it contains information that helps us along.

A thing that I personally find noteworthy is that during the boot sequence it gives the following message:
[FAILED] Failed to start Load Kernel Modules
I feel like the root of our problem lies with this, but that's just a gut feeling - I'm not quite an expert on Pi systems :)

"dmesg" gives:

Code: Select all

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 6.1.28-v7l+ (dom@buildbot) (arm-linux-gnueabihf-gcc-8 (Ubuntu/Linaro 8.4.0-3ubuntu1) 8.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1651 SMP Wed May 17 14:32:54 BST 2023
[    0.000000] CPU: ARMv7 Processor [410fd083] revision 3 (ARMv7), cr=30c5383d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Raspberry Pi Compute Module 4S Rev 1.0
[    0.000000] random: crng init done
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created CMA memory pool at 0x000000002ac00000, size 64 MiB
[    0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000000000-0x000000002fffffff]
[    0.000000]   Normal   empty
[    0.000000]   HighMem  [mem 0x0000000030000000-0x000000003b3fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x000000003b3fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000003b3fffff]
[    0.000000] percpu: Embedded 17 pages/cpu s36884 r8192 d24556 u69632
[    0.000000] pcpu-alloc: s36884 r8192 d24556 u69632 alloc=17*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 240960
[    0.000000] Kernel command line: coherent_pool=1M snd_bcm2835.enable_headphones=0 snd_bcm2835.enable_hdmi=1 bcm2708_fb.fbwidth=1280 bcm2708_fb.fbheight=1024 bcm2708_fb.fbswap=1 smsc95xx.macaddr=B8:27:EB:A7:3E:B2 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000  dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 fsck.repair=yes rootwait nosplash plymouth.ignore-serial-consoles
[    0.000000] Unknown kernel command line parameters "nosplash", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 876732K/970752K available (10240K kernel code, 1502K rwdata, 3132K rodata, 2048K init, 634K bss, 28484K reserved, 65536K cma-reserved, 184320K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 37107 entries in 109 pages
[    0.000000] ftrace: allocated 109 pages with 5 groups
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] 	Rude variant of Tasks RCU enabled.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns
[    0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns
[    0.000016] Switching to timer-based delay loop, resolution 18ns
[    0.000329] Console: colour dummy device 80x30
[    0.000824] printk: console [tty1] enabled
[    0.000883] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.00 BogoMIPS (lpj=540000)
[    0.000922] pid_max: default: 32768 minimum: 301
[    0.001047] LSM: Security Framework initializing
[    0.001232] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.001271] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.002469] cgroup: Disabling memory control group subsystem
[    0.002669] CPU: Testing write buffer coherency: ok
[    0.002735] CPU0: Spectre BHB: enabling loop workaround for all CPUs
[    0.003080] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.003994] cblist_init_generic: Setting adjustable number of callback queues.
[    0.004025] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.004152] cblist_init_generic: Setting shift to 2 and lim to 1.
[    0.004297] Setting up static identity map for 0x200000 - 0x20003c
[    0.004460] rcu: Hierarchical SRCU implementation.
[    0.004482] rcu: 	Max phase no-delay instances is 1000.
[    0.005231] smp: Bringing up secondary CPUs ...
[    0.006131] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.007117] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.008089] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.008204] smp: Brought up 1 node, 4 CPUs
[    0.008269] SMP: Total of 4 processors activated (432.00 BogoMIPS).
[    0.008293] CPU: All CPU(s) started in HYP mode.
[    0.008311] CPU: Virtualization extensions available.
[    0.008928] devtmpfs: initialized
[    0.020594] VFP support v0.3: implementor 41 architecture 3 part 40 variant 8 rev 0
[    0.020812] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.020856] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.022570] pinctrl core: initialized pinctrl subsystem
[    0.023527] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.026456] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.027061] audit: initializing netlink subsys (disabled)
[    0.027263] audit: type=2000 audit(0.020:1): state=initialized audit_enabled=0 res=1
[    0.027783] thermal_sys: Registered thermal governor 'step_wise'
[    0.028408] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.028455] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.028833] Serial: AMBA PL011 UART driver
[    0.037176] bcm2835-mbox fe00b880.mailbox: mailbox enabled
[    0.060053] raspberrypi-firmware soc:firmware: Attached to firmware from 2023-04-25T18:26:03, variant start
[    0.070063] raspberrypi-firmware soc:firmware: Firmware hash is d7f9c2b4ef7e4a8c0b04374a879ce89d7a948453
[    0.109736] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.118116] bcm2835-dma fe007000.dma: DMA legacy API manager, dmachans=0x1
[    0.121498] SCSI subsystem initialized
[    0.121707] usbcore: registered new interface driver usbfs
[    0.121770] usbcore: registered new interface driver hub
[    0.121833] usbcore: registered new device driver usb
[    0.122062] usb_phy_generic phy: supply vcc not found, using dummy regulator
[    0.122224] usb_phy_generic phy: dummy supplies not allowed for exclusive requests
[    0.122475] pps_core: LinuxPPS API ver. 1 registered
[    0.122498] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.122538] PTP clock support registered
[    0.123472] vgaarb: loaded
[    1.348054] clocksource: Switched to clocksource arch_sys_counter
[    1.376535] VFS: Disk quotas dquot_6.6.0
[    1.376629] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.376771] FS-Cache: Loaded
[    1.376995] CacheFiles: Loaded
[    1.385653] NET: Registered PF_INET protocol family
[    1.385958] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    1.387938] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    1.387990] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    1.388073] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    1.388151] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    1.388296] TCP: Hash tables configured (established 8192 bind 8192)
[    1.388441] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.388491] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    1.388696] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    1.389232] RPC: Registered named UNIX socket transport module.
[    1.389260] RPC: Registered udp transport module.
[    1.389279] RPC: Registered tcp transport module.
[    1.389297] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    1.389327] PCI: CLS 0 bytes, default 64
[    1.391008] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[    1.431189] Initialise system trusted keyrings
[    1.431542] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[    1.438431] zbud: loaded
[    1.440630] NFS: Registering the id_resolver key type
[    1.440672] Key type id_resolver registered
[    1.440692] Key type id_legacy registered
[    1.440800] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    1.440825] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    1.441922] Key type asymmetric registered
[    1.441949] Asymmetric key parser 'x509' registered
[    1.442190] bounce: pool size: 64 pages
[    1.442330] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    1.442536] io scheduler mq-deadline registered
[    1.442562] io scheduler kyber registered
[    1.450055] bcm2708_fb soc:fb: FB found 1 display(s)
[    1.467059] Console: switching to colour frame buffer device 160x64
[    1.473039] bcm2708_fb soc:fb: Registered framebuffer for display 0, size 1280x1024
[    1.481963] iproc-rng200 fe104000.rng: hwrng registered
[    1.482203] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[    1.483331] gpiomem-bcm2835 fe200000.gpiomem: Initialised: Registers at 0xfe200000
[    1.494057] brd: module loaded
[    1.501215] loop: module loaded
[    1.501804] Loading iSCSI transport class v2.0-870.
[    1.505428] usbcore: registered new interface driver r8152
[    1.505560] usbcore: registered new interface driver lan78xx
[    1.505664] usbcore: registered new interface driver smsc95xx
[    1.506078] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.506288] dwc_otg: FIQ enabled
[    1.506298] dwc_otg: NAK holdoff enabled
[    1.506307] dwc_otg: FIQ split-transaction FSM enabled
[    1.506321] Module dwc_common_port init
[    1.506635] usbcore: registered new interface driver uas
[    1.506749] usbcore: registered new interface driver usb-storage
[    1.506976] mousedev: PS/2 mouse device common for all mice
[    1.510767] sdhci: Secure Digital Host Controller Interface driver
[    1.510850] sdhci: Copyright(c) Pierre Ossman
[    1.511197] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.512944] ledtrig-cpu: registered to indicate activity on CPUs
[    1.513234] hid: raw HID events driver (C) Jiri Kosina
[    1.513396] usbcore: registered new interface driver usbhid
[    1.513460] usbhid: USB HID core driver
[    1.513645] bcm2835_vchiq fe00b840.mailbox: there is not valid maps for state default
[    1.518642] Initializing XFRM netlink socket
[    1.518746] NET: Registered PF_PACKET protocol family
[    1.518882] Key type dns_resolver registered
[    1.519419] Registering SWP/SWPB emulation handler
[    1.520141] registered taskstats version 1
[    1.520243] Loading compiled-in X.509 certificates
[    1.521113] Key type .fscrypt registered
[    1.523652] Key type fscrypt-provisioning registered
[    1.538107] uart-pl011 fe201000.serial: cts_event_workaround enabled
[    1.540465] fe201000.serial: ttyAMA0 at MMIO 0xfe201000 (irq = 46, base_baud = 0) is a PL011 rev2
[    1.544769] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer
[    1.547376] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver
[    1.552049] of_cfs_init
[    1.554492] of_cfs_init: OK
[    1.580650] mmc0: SDHCI controller on fe340000.mmc [fe340000.mmc] using ADMA
[    1.583439] Waiting for root device /dev/mmcblk0p2...
[    1.647526] mmc0: new DDR MMC card at address 0001
[    1.650730] mmcblk0: mmc0:0001 AJTD4R 14.6 GiB 
[    1.655222]  mmcblk0: p1 p2
[    1.657987] mmcblk0: mmc0:0001 AJTD4R 14.6 GiB
[    1.660691] mmcblk0boot0: mmc0:0001 AJTD4R 4.00 MiB 
[    1.664877] mmcblk0boot1: mmc0:0001 AJTD4R 4.00 MiB 
[    1.668743] mmcblk0rpmb: mmc0:0001 AJTD4R 4.00 MiB, chardev (242:0)
[    1.703501] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Quota mode: none.
[    1.705833] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.708635] devtmpfs: mounted
[    1.718956] Freeing unused kernel image (initmem) memory: 2048K
[    1.738347] Run /sbin/init as init process
[    1.740575]   with arguments:
[    1.740584]     /sbin/init
[    1.740593]     nosplash
[    1.740601]   with environment:
[    1.740609]     HOME=/
[    1.740618]     TERM=linux
[    1.972252] systemd[1]: System time before build time, advancing clock.
[    2.144561] NET: Registered PF_INET6 protocol family
[    2.148228] Segment Routing with IPv6
[    2.150530] In-situ OAM (IOAM) with IPv6
[    2.203028] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    2.214563] systemd[1]: Detected architecture arm.
[    2.328238] systemd[1]: Set hostname to <RevPi87109>.
[    2.755144] systemd[1]: /lib/systemd/system/teamviewer-iot-mon-agent.service:7: PIDFile= references path below legacy directory /var/run/, updating /var/run/teamviewer-iot-mon-agent.pid → /run/teamviewer-iot-mon-agent.pid; please update the unit file accordingly.
[    2.833400] systemd[1]: /lib/systemd/system/revpipyload.service:7: PIDFile= references path below legacy directory /var/run/, updating /var/run/revpipyload.pid → /run/revpipyload.pid; please update the unit file accordingly.
[    2.858329] systemd[1]: /lib/systemd/system/noderedrevpinodes-server.service:5: Unknown lvalue 'MemoryAccounting' in section 'Unit', ignoring
[    2.861061] systemd[1]: /lib/systemd/system/noderedrevpinodes-server.service:6: Unknown lvalue 'MemoryHigh' in section 'Unit', ignoring
[    2.863809] systemd[1]: /lib/systemd/system/noderedrevpinodes-server.service:7: Unknown lvalue 'MemoryMax' in section 'Unit', ignoring
[    3.047404] systemd[1]: Created slice User and Session Slice.
[    3.054285] systemd[1]: Listening on fsck to fsckd communication Socket.
[    3.258818] i2c_dev: i2c /dev entries driver
[    3.580717] EXT4-fs (mmcblk0p2): re-mounted. Quota mode: none.
[    4.163205] systemd-journald[165]: Received request to flush runtime journal from PID 1
[    7.426790] mc: Linux media interface: v0.10
[    7.740189] videodev: Linux video capture interface: v2.00
[    7.999133] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[    8.001165] bcm2835_vc_sm_cma_probe: Videocore shared memory driver
[    8.001192] [vc_sm_connected_init]: start
[    8.007456] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[    8.044864] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[    8.049330] [vc_sm_connected_init]: installed successfully
[    8.056752] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[    8.062519] rpivid_hevc: module is from the staging directory, the quality is unknown, you have been warned.
[    8.064453] vc_sm_cma: module is from the staging directory, the quality is unknown, you have been warned.
[    8.074911] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[    8.086480] rpivid feb10000.codec: Device registered as /dev/video19
[    8.099274] bcm2835_v4l2: module is from the staging directory, the quality is unknown, you have been warned.
[    8.100494] bcm2835_mmal_vchiq: module is from the staging directory, the quality is unknown, you have been warned.
[    8.116623] bcm2835_codec: module is from the staging directory, the quality is unknown, you have been warned.
[    8.117791] bcm2835_isp: module is from the staging directory, the quality is unknown, you have been warned.
[    8.141391] bcm2835-isp bcm2835-isp: Device node output[0] registered as /dev/video13
[    8.141892] bcm2835-isp bcm2835-isp: Device node capture[0] registered as /dev/video14
[    8.142268] bcm2835-isp bcm2835-isp: Device node capture[1] registered as /dev/video15
[    8.142310] bcm2835-codec bcm2835-codec: Device registered as /dev/video10
[    8.142358] bcm2835-codec bcm2835-codec: Loaded V4L2 decode
[    8.142725] bcm2835-isp bcm2835-isp: Device node stats[2] registered as /dev/video16
[    8.142747] bcm2835-isp bcm2835-isp: Register output node 0 with media controller
[    8.142776] bcm2835-isp bcm2835-isp: Register capture node 1 with media controller
[    8.142792] bcm2835-isp bcm2835-isp: Register capture node 2 with media controller
[    8.142807] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller
[    8.159344] bcm2835-isp bcm2835-isp: Device node output[0] registered as /dev/video20
[    8.159447] bcm2835-codec bcm2835-codec: Device registered as /dev/video11
[    8.159513] bcm2835-codec bcm2835-codec: Loaded V4L2 encode
[    8.160137] bcm2835-isp bcm2835-isp: Device node capture[0] registered as /dev/video21
[    8.160736] bcm2835-isp bcm2835-isp: Device node capture[1] registered as /dev/video22
[    8.161201] bcm2835-isp bcm2835-isp: Device node stats[2] registered as /dev/video23
[    8.161228] bcm2835-isp bcm2835-isp: Register output node 0 with media controller
[    8.161248] bcm2835-isp bcm2835-isp: Register capture node 1 with media controller
[    8.161264] bcm2835-isp bcm2835-isp: Register capture node 2 with media controller
[    8.161279] bcm2835-isp bcm2835-isp: Register capture node 3 with media controller
[    8.161538] bcm2835-isp bcm2835-isp: Loaded V4L2 bcm2835-isp
[    8.173201] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[    8.176394] bcm2835-codec bcm2835-codec: Device registered as /dev/video12
[    8.176439] bcm2835-codec bcm2835-codec: Loaded V4L2 isp
[    8.197686] bcm2835-codec bcm2835-codec: Device registered as /dev/video18
[    8.197740] bcm2835-codec bcm2835-codec: Loaded V4L2 image_fx
[    8.211492] bcm2835-codec bcm2835-codec: Device registered as /dev/video31
[    8.211575] bcm2835-codec bcm2835-codec: Loaded V4L2 encode_image
[    8.244886] bcm2835_audio bcm2835_audio: card created with 8 channels
[    8.508184] dwc2 fe980000.usb: supply vusb_d not found, using dummy regulator
[    8.508476] dwc2 fe980000.usb: supply vusb_a not found, using dummy regulator
[    8.561079] dwc2 fe980000.usb: DWC OTG Controller
[    8.561132] dwc2 fe980000.usb: new USB bus registered, assigned bus number 1
[    8.561191] dwc2 fe980000.usb: irq 51, io mem 0xfe980000
[    8.561497] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    8.561523] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    8.561546] usb usb1: Product: DWC OTG Controller
[    8.561573] usb usb1: Manufacturer: Linux 6.1.28-v7l+ dwc2_hsotg
[    8.561591] usb usb1: SerialNumber: fe980000.usb
[    8.566133] hub 1-0:1.0: USB hub found
[    8.566221] hub 1-0:1.0: 1 port detected
[    8.918122] usb 1-1: new high-speed USB device number 2 using dwc2
[    9.168604] usb 1-1: New USB device found, idVendor=0424, idProduct=9514, bcdDevice= 2.00
[    9.168640] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    9.169511] hub 1-1:1.0: USB hub found
[    9.169634] hub 1-1:1.0: 5 ports detected
[    9.498123] usb 1-1.1: new high-speed USB device number 3 using dwc2
[    9.628632] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00, bcdDevice= 2.00
[    9.628670] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    9.632024] smsc95xx v2.0.0
[    9.801368] SMSC LAN8700 usb-001:003:01: attached PHY driver (mii_bus:phy_addr=usb-001:003:01, irq=52)
[    9.802770] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-fe980000.usb-1.1, smsc95xx USB 2.0 Ethernet, c8:3e:a7:10:58:a2
[    9.899429] usb 1-1.2: new low-speed USB device number 4 using dwc2
[   10.033877] usb 1-1.2: New USB device found, idVendor=413c, idProduct=301a, bcdDevice= 1.00
[   10.033903] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   10.033918] usb 1-1.2: Product: Dell MS116 USB Optical Mouse
[   10.033931] usb 1-1.2: Manufacturer: PixArt
[   10.040858] input: PixArt Dell MS116 USB Optical Mouse as /devices/platform/soc/fe980000.usb/usb1/1-1/1-1.2/1-1.2:1.0/0003:413C:301A.0001/input/input0
[   10.045535] hid-generic 0003:413C:301A.0001: input,hidraw0: USB HID v1.11 Mouse [PixArt Dell MS116 USB Optical Mouse] on usb-fe980000.usb-1.2/input0
[   10.138115] usb 1-1.3: new low-speed USB device number 5 using dwc2
[   10.285179] usb 1-1.3: New USB device found, idVendor=413c, idProduct=2113, bcdDevice= 1.08
[   10.285232] usb 1-1.3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[   10.285265] usb 1-1.3: Product: Dell KB216 Wired Keyboard
[   10.291922] input: Dell KB216 Wired Keyboard as /devices/platform/soc/fe980000.usb/usb1/1-1/1-1.3/1-1.3:1.0/0003:413C:2113.0002/input/input1
[   10.360181] hid-generic 0003:413C:2113.0002: input,hidraw1: USB HID v1.11 Keyboard [Dell KB216 Wired Keyboard] on usb-fe980000.usb-1.3/input0
[   10.367261] input: Dell KB216 Wired Keyboard System Control as /devices/platform/soc/fe980000.usb/usb1/1-1/1-1.3/1-1.3:1.1/0003:413C:2113.0003/input/input2
[   10.399514] Adding 102396k swap on /var/swap.  Priority:-2 extents:1 across:102396k SSFS
[   10.436006] input: Dell KB216 Wired Keyboard Consumer Control as /devices/platform/soc/fe980000.usb/usb1/1-1/1-1.3/1-1.3:1.1/0003:413C:2113.0003/input/input3
[   10.439324] hid-generic 0003:413C:2113.0003: input,hidraw2: USB HID v1.11 Device [Dell KB216 Wired Keyboard] on usb-fe980000.usb-1.3/input1
[   10.538164] usb 1-1.5: new high-speed USB device number 6 using dwc2
[   10.668756] usb 1-1.5: New USB device found, idVendor=0424, idProduct=9512, bcdDevice= 2.00
[   10.668788] usb 1-1.5: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   10.669691] hub 1-1.5:1.0: USB hub found
[   10.669880] hub 1-1.5:1.0: 3 ports detected
[   10.988165] usb 1-1.5.1: new high-speed USB device number 7 using dwc2
[   11.119152] usb 1-1.5.1: New USB device found, idVendor=0424, idProduct=ec00, bcdDevice= 2.00
[   11.119195] usb 1-1.5.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   11.125755] smsc95xx v2.0.0
[   11.269387] SMSC LAN8700 usb-001:007:01: attached PHY driver (mii_bus:phy_addr=usb-001:007:01, irq=53)
[   11.286269] smsc95xx 1-1.5.1:1.0 eth1: register 'smsc95xx' at usb-fe980000.usb-1.5.1, smsc95xx USB 2.0 Ethernet, c8:3e:a7:10:58:a3
[   11.388560] usb 1-1.5.2: new full-speed USB device number 8 using dwc2
[   11.393750] 8021q: 802.1Q VLAN Support v1.8
[   11.526796] usb 1-1.5.2: New USB device found, idVendor=0403, idProduct=6001, bcdDevice= 6.00
[   11.526811] usb 1-1.5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   11.526818] usb 1-1.5.2: Product: FT232R USB UART
[   11.526824] usb 1-1.5.2: Manufacturer: FTDI
[   11.526829] usb 1-1.5.2: SerialNumber: AU06I1EG
[   11.549219] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   11.609935] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   11.613021] cfg80211: loaded regulatory.db is malformed or signature is missing/invalid
[   11.628082] usb 1-1.5.3: new full-speed USB device number 9 using dwc2
[   11.772745] usb 1-1.5.3: New USB device found, idVendor=0403, idProduct=6001, bcdDevice= 6.00
[   11.772760] usb 1-1.5.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   11.772772] usb 1-1.5.3: Product: FT232R USB UART
[   11.772781] usb 1-1.5.3: Manufacturer: FTDI
[   11.772792] usb 1-1.5.3: SerialNumber: AU06I16M
[   13.159124] rtc-pcf2127-i2c 1-0051: registered as rtc0
[   13.160262] rtc-pcf2127-i2c 1-0051: setting system clock to 2023-07-12T13:46:54 UTC (1689169614)
[   13.761959] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[   13.765458] smsc95xx 1-1.1:1.0 eth0: Link is Up - 100Mbps/Full - flow control off
[   13.765503] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   13.871586] usbcore: registered new interface driver usbserial_generic
[   13.871625] usbserial: USB Serial support registered for generic
[   13.880943] usbcore: registered new interface driver ftdi_sio
[   13.880993] usbserial: USB Serial support registered for FTDI USB Serial Device
[   13.881129] ftdi_sio 1-1.5.2:1.0: FTDI USB Serial Device converter detected
[   13.881244] usb 1-1.5.2: Detected FT232R
[   13.900332] usb 1-1.5.2: FTDI USB Serial Device converter now attached to ttyUSB0
[   13.901558] ftdi_sio 1-1.5.3:1.0: FTDI USB Serial Device converter detected
[   13.902141] usb 1-1.5.3: Detected FT232R
[   13.903214] usb 1-1.5.3: FTDI USB Serial Device converter now attached to ttyUSB1
[   14.052253] smsc95xx 1-1.5.1:1.0 eth1: hardware isn't capable of remote wakeup
[   14.055731] smsc95xx 1-1.5.1:1.0 eth1: Link is Down
[   29.027425] fuse: init (API version 7.37)
[   47.700602] smsc95xx 1-1.1:1.0 eth0: Link is Down
[   49.436573] smsc95xx 1-1.1:1.0 eth0: Link is Up - 100Mbps/Full - flow control off
"uname -a" gives "Linux RevPi87109 6.1.28-v7l+ #1651 SMP Wed May 17 14:32:54 BST 2023 armv7l GNU/Linux"

"cat /etc/revpi/image-release" gives "2022-07-28-revpi-buster.img"

"cat /boot/config.txt" gives:

Code: Select all

# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

# Enable DRM VC4 V3D driver
#dtoverlay=vc4-kms-v3d
#max_framebuffers=2

[pi4]
[cm4s]
dtoverlay=dwc2,dr_mode=host

[all]
enable_uart=1
#dtoverlay=w1-gpio
dtoverlay=revpi-con-can
dtoverlay=revpi-connect-se
dtparam=eth0_mac_hi=0xc83ea710
dtparam=eth0_mac_lo=0x58a2
dtparam=eth1_mac_hi=0xc83ea710
dtparam=eth1_mac_lo=0x58a3
"cat /etc/revpi/config.rsc" follows in the next post, I'm hitting the character limit :?
JeffreyA
Posts: 2
Joined: 13 Jul 2023, 10:49
Answers: 0

Re: power led of DO module keeps flashing red

Post by JeffreyA »

Follow up of the previous post, the result of "cat /etc/revpi/config.rsc":

Code: Select all

{"App":{"name": "PiCtory", "version": "2.0.6","saveTS": "20230712132536","language": "en","layout": {"north":{"size":70,"initClosed":false,"initHidden":false},"south":{"size":200,"initClosed":false,"initHidden":false,"children":{"layout1":{"east":{"size":500,"initClosed":false,"initHidden":false}}}},"east":{"size":70,"initClosed":true,"initHidden":false,"children":{}},"west":{"size":200,"initClosed":false,"initHidden":false,"children":{"layout1":{}}}}},"Summary":{"inpTotal": 216,"outTotal": 59},"Devices":[{"GUID": "e6286f42-05e9-95b2-9a00-b6925e877727","id": "device_RevPiDO_20160818_1_0_003","type": "LEFT_RIGHT","productType": "98","position": "29","name": "RevPi DO","bmk": "RevPi DO","inpVariant": 0,"outVariant": 0,"comment": "","offset": 0,"inp": {"0": ["Output_Status_i04","0","16","2",false,"0000", "",""],"1": ["Status_i04","0","16","4",false,"0001", "",""],"2": ["Input_i04","0","16","0",false,"0038", "",""],"3": ["Counter_1_i04","0","32","6",false,"0039", "",""],"4": ["Counter_2_i04","0","32","10",false,"0040", "",""],"5": ["Counter_3_i04","0","32","14",false,"0041", "",""],"6": ["Counter_4_i04","0","32","18",false,"0042", "",""],"7": ["Counter_5_i04","0","32","22",false,"0043", "",""],"8": ["Counter_6_i04","0","32","26",false,"0044", "",""],"9": ["Counter_7_i04","0","32","30",false,"0045", "",""],"10": ["Counter_8_i04","0","32","34",false,"0046", "",""],"11": ["Counter_9_i04","0","32","38",false,"0047", "",""],"12": ["Counter_10_i04","0","32","42",false,"0048", "",""],"13": ["Counter_11_i04","0","32","46",false,"0049", "",""],"14": ["Counter_12_i04","0","32","50",false,"0050", "",""],"15": ["Counter_13_i04","0","32","54",false,"0051", "",""],"16": ["Counter_14_i04","0","32","58",false,"0052", "",""],"17": ["Counter_15_i04","0","32","62",false,"0053", "",""],"18": ["Counter_16_i04","0","32","66",false,"0054", "",""]},"out": {"0": ["O_1_i04","0","1","70",true,"0002", "","0"],"1": ["O_2_i04","0","1","70",true,"0003", "","1"],"2": ["O_3_i04","0","1","70",true,"0004", "","2"],"3": ["O_4_i04","0","1","70",true,"0005", "","3"],"4": ["O_5_i04","0","1","70",true,"0006", "","4"],"5": ["O_6_i04","0","1","70",true,"0007", "","5"],"6": ["O_7_i04","0","1","70",true,"0008", "","6"],"7": ["O_8_i04","0","1","70",true,"0009", "","7"],"8": ["O_9_i04","0","1","70",true,"0010", "","8"],"9": ["O_10_i04","0","1","70",true,"0011", "","9"],"10": ["O_11_i04","0","1","70",true,"0012", "","10"],"11": ["O_12_i04","0","1","70",true,"0013", "","11"],"12": ["O_13_i04","0","1","70",true,"0014", "","12"],"13": ["O_14_i04","0","1","70",true,"0015", "","13"],"14": ["O_15_i04","0","1","70",true,"0016", "","14"],"15": ["O_16_i04","0","1","70",true,"0017", "","15"],"16": ["PWM_1_i04","0","8","72",false,"0018", "",""],"17": ["PWM_2_i04","0","8","73",false,"0019", "",""],"18": ["PWM_3_i04","0","8","74",false,"0020", "",""],"19": ["PWM_4_i04","0","8","75",false,"0021", "",""],"20": ["PWM_5_i04","0","8","76",false,"0022", "",""],"21": ["PWM_6_i04","0","8","77",false,"0023", "",""],"22": ["PWM_7_i04","0","8","78",false,"0024", "",""],"23": ["PWM_8_i04","0","8","79",false,"0025", "",""],"24": ["PWM_9_i04","0","8","80",false,"0026", "",""],"25": ["PWM_10_i04","0","8","81",false,"0027", "",""],"26": ["PWM_11_i04","0","8","82",false,"0028", "",""],"27": ["PWM_12_i04","0","8","83",false,"0029", "",""],"28": ["PWM_13_i04","0","8","84",false,"0030", "",""],"29": ["PWM_14_i04","0","8","85",false,"0031", "",""],"30": ["PWM_15_i04","0","8","86",false,"0032", "",""],"31": ["PWM_16_i04","0","8","87",false,"0033", "",""]},"mem": {"0": ["OutputPushPull_i04","0","16","106",false,"0034", "",""],"1": ["OutputOpenLoadDetect_i04","0","16","108",false,"0035", "",""],"2": ["OutputPWMActive_i04","0","16","110",false,"0036", "",""],"3": ["OutputPWMFrequency_i04","1","8","112",false,"0037", "",""],"4": ["InputMode_1_i04","0","8","88",false,"0055", "",""],"5": ["InputMode_2_i04","0","8","89",false,"0056", "",""],"6": ["InputMode_3_i04","0","8","90",false,"0057", "",""],"7": ["InputMode_4_i04","0","8","91",false,"0058", "",""],"8": ["InputMode_5_i04","0","8","92",false,"0059", "",""],"9": ["InputMode_6_i04","0","8","93",false,"0060", "",""],"10": ["InputMode_7_i04","0","8","94",false,"0061", "",""],"11": ["InputMode_8_i04","0","8","95",false,"0062", "",""],"12": ["InputMode_9_i04","0","8","96",false,"0063", "",""],"13": ["InputMode_10_i04","0","8","97",false,"0064", "",""],"14": ["InputMode_11_i04","0","8","98",false,"0065", "",""],"15": ["InputMode_12_i04","0","8","99",false,"0066", "",""],"16": ["InputMode_13_i04","0","8","100",false,"0067", "",""],"17": ["InputMode_14_i04","0","8","101",false,"0068", "",""],"18": ["InputMode_15_i04","0","8","102",false,"0069", "",""],"19": ["InputMode_16_i04","0","8","103",false,"0070", "",""],"20": ["InputDebounce_i04","0","16","104",false,"0071", "",""]},"extend": {}},{"GUID": "95fb3f9d-b6c3-1e44-62c5-620aa3143630","id": "device_RevPiDO_20160818_1_0_002","type": "LEFT_RIGHT","productType": "98","position": "30","name": "RevPi DO","bmk": "RevPi DO","inpVariant": 0,"outVariant": 0,"comment": "","offset": 113,"inp": {"0": ["Output_Status_i03","0","16","2",false,"0000", "",""],"1": ["Status_i03","0","16","4",false,"0001", "",""],"2": ["Input_i03","0","16","0",false,"0038", "",""],"3": ["Counter_1_i03","0","32","6",false,"0039", "",""],"4": ["Counter_2_i03","0","32","10",false,"0040", "",""],"5": ["Counter_3_i03","0","32","14",false,"0041", "",""],"6": ["Counter_4_i03","0","32","18",false,"0042", "",""],"7": ["Counter_5_i03","0","32","22",false,"0043", "",""],"8": ["Counter_6_i03","0","32","26",false,"0044", "",""],"9": ["Counter_7_i03","0","32","30",false,"0045", "",""],"10": ["Counter_8_i03","0","32","34",false,"0046", "",""],"11": ["Counter_9_i03","0","32","38",false,"0047", "",""],"12": ["Counter_10_i03","0","32","42",false,"0048", "",""],"13": ["Counter_11_i03","0","32","46",false,"0049", "",""],"14": ["Counter_12_i03","0","32","50",false,"0050", "",""],"15": ["Counter_13_i03","0","32","54",false,"0051", "",""],"16": ["Counter_14_i03","0","32","58",false,"0052", "",""],"17": ["Counter_15_i03","0","32","62",false,"0053", "",""],"18": ["Counter_16_i03","0","32","66",false,"0054", "",""]},"out": {"0": ["O_1_i03","0","1","70",true,"0002", "","0"],"1": ["O_2_i03","0","1","70",true,"0003", "","1"],"2": ["O_3_i03","0","1","70",true,"0004", "","2"],"3": ["O_4_i03","0","1","70",true,"0005", "","3"],"4": ["O_5_i03","0","1","70",true,"0006", "","4"],"5": ["O_6_i03","0","1","70",true,"0007", "","5"],"6": ["O_7_i03","0","1","70",true,"0008", "","6"],"7": ["O_8_i03","0","1","70",true,"0009", "","7"],"8": ["O_9_i03","0","1","70",true,"0010", "","8"],"9": ["O_10_i03","0","1","70",true,"0011", "","9"],"10": ["O_11_i03","0","1","70",true,"0012", "","10"],"11": ["O_12_i03","0","1","70",true,"0013", "","11"],"12": ["O_13_i03","0","1","70",true,"0014", "","12"],"13": ["O_14_i03","0","1","70",true,"0015", "","13"],"14": ["O_15_i03","0","1","70",true,"0016", "","14"],"15": ["O_16_i03","0","1","70",true,"0017", "","15"],"16": ["PWM_1_i03","0","8","72",false,"0018", "",""],"17": ["PWM_2_i03","0","8","73",false,"0019", "",""],"18": ["PWM_3_i03","0","8","74",false,"0020", "",""],"19": ["PWM_4_i03","0","8","75",false,"0021", "",""],"20": ["PWM_5_i03","0","8","76",false,"0022", "",""],"21": ["PWM_6_i03","0","8","77",false,"0023", "",""],"22": ["PWM_7_i03","0","8","78",false,"0024", "",""],"23": ["PWM_8_i03","0","8","79",false,"0025", "",""],"24": ["PWM_9_i03","0","8","80",false,"0026", "",""],"25": ["PWM_10_i03","0","8","81",false,"0027", "",""],"26": ["PWM_11_i03","0","8","82",false,"0028", "",""],"27": ["PWM_12_i03","0","8","83",false,"0029", "",""],"28": ["PWM_13_i03","0","8","84",false,"0030", "",""],"29": ["PWM_14_i03","0","8","85",false,"0031", "",""],"30": ["PWM_15_i03","0","8","86",false,"0032", "",""],"31": ["PWM_16_i03","0","8","87",false,"0033", "",""]},"mem": {"0": ["OutputPushPull_i03","0","16","106",false,"0034", "",""],"1": ["OutputOpenLoadDetect_i03","0","16","108",false,"0035", "",""],"2": ["OutputPWMActive_i03","0","16","110",false,"0036", "",""],"3": ["OutputPWMFrequency_i03","1","8","112",false,"0037", "",""],"4": ["InputMode_1_i03","0","8","88",false,"0055", "",""],"5": ["InputMode_2_i03","0","8","89",false,"0056", "",""],"6": ["InputMode_3_i03","0","8","90",false,"0057", "",""],"7": ["InputMode_4_i03","0","8","91",false,"0058", "",""],"8": ["InputMode_5_i03","0","8","92",false,"0059", "",""],"9": ["InputMode_6_i03","0","8","93",false,"0060", "",""],"10": ["InputMode_7_i03","0","8","94",false,"0061", "",""],"11": ["InputMode_8_i03","0","8","95",false,"0062", "",""],"12": ["InputMode_9_i03","0","8","96",false,"0063", "",""],"13": ["InputMode_10_i03","0","8","97",false,"0064", "",""],"14": ["InputMode_11_i03","0","8","98",false,"0065", "",""],"15": ["InputMode_12_i03","0","8","99",false,"0066", "",""],"16": ["InputMode_13_i03","0","8","100",false,"0067", "",""],"17": ["InputMode_14_i03","0","8","101",false,"0068", "",""],"18": ["InputMode_15_i03","0","8","102",false,"0069", "",""],"19": ["InputMode_16_i03","0","8","103",false,"0070", "",""],"20": ["InputDebounce_i03","0","16","104",false,"0071", "",""]},"extend": {}},{"GUID": "61610d4c-0999-0425-15fd-305b035eb879","id": "device_RevPiDO_20160818_1_0_001","type": "LEFT_RIGHT","productType": "98","position": "31","name": "RevPi DO","bmk": "RevPi DO","inpVariant": 0,"outVariant": 0,"comment": "","offset": 226,"inp": {"0": ["Output_Status","0","16","2",false,"0000", "",""],"1": ["Status","0","16","4",false,"0001", "",""],"2": ["Input","0","16","0",false,"0038", "",""],"3": ["Counter_1","0","32","6",false,"0039", "",""],"4": ["Counter_2","0","32","10",false,"0040", "",""],"5": ["Counter_3","0","32","14",false,"0041", "",""],"6": ["Counter_4","0","32","18",false,"0042", "",""],"7": ["Counter_5","0","32","22",false,"0043", "",""],"8": ["Counter_6","0","32","26",false,"0044", "",""],"9": ["Counter_7","0","32","30",false,"0045", "",""],"10": ["Counter_8","0","32","34",false,"0046", "",""],"11": ["Counter_9","0","32","38",false,"0047", "",""],"12": ["Counter_10","0","32","42",false,"0048", "",""],"13": ["Counter_11","0","32","46",false,"0049", "",""],"14": ["Counter_12","0","32","50",false,"0050", "",""],"15": ["Counter_13","0","32","54",false,"0051", "",""],"16": ["Counter_14","0","32","58",false,"0052", "",""],"17": ["Counter_15","0","32","62",false,"0053", "",""],"18": ["Counter_16","0","32","66",false,"0054", "",""]},"out": {"0": ["O_1","0","1","70",true,"0002", "","0"],"1": ["O_2","0","1","70",true,"0003", "","1"],"2": ["O_3","0","1","70",true,"0004", "","2"],"3": ["O_4","0","1","70",true,"0005", "","3"],"4": ["O_5","0","1","70",true,"0006", "","4"],"5": ["O_6","0","1","70",true,"0007", "","5"],"6": ["O_7","0","1","70",true,"0008", "","6"],"7": ["O_8","0","1","70",true,"0009", "","7"],"8": ["O_9","0","1","70",true,"0010", "","8"],"9": ["O_10","0","1","70",true,"0011", "","9"],"10": ["O_11","0","1","70",true,"0012", "","10"],"11": ["O_12","0","1","70",true,"0013", "","11"],"12": ["O_13","0","1","70",true,"0014", "","12"],"13": ["O_14","0","1","70",true,"0015", "","13"],"14": ["O_15","0","1","70",true,"0016", "","14"],"15": ["O_16","0","1","70",true,"0017", "","15"],"16": ["PWM_1","0","8","72",false,"0018", "",""],"17": ["PWM_2","0","8","73",false,"0019", "",""],"18": ["PWM_3","0","8","74",false,"0020", "",""],"19": ["PWM_4","0","8","75",false,"0021", "",""],"20": ["PWM_5","0","8","76",false,"0022", "",""],"21": ["PWM_6","0","8","77",false,"0023", "",""],"22": ["PWM_7","0","8","78",false,"0024", "",""],"23": ["PWM_8","0","8","79",false,"0025", "",""],"24": ["PWM_9","0","8","80",false,"0026", "",""],"25": ["PWM_10","0","8","81",false,"0027", "",""],"26": ["PWM_11","0","8","82",false,"0028", "",""],"27": ["PWM_12","0","8","83",false,"0029", "",""],"28": ["PWM_13","0","8","84",false,"0030", "",""],"29": ["PWM_14","0","8","85",false,"0031", "",""],"30": ["PWM_15","0","8","86",false,"0032", "",""],"31": ["PWM_16","0","8","87",false,"0033", "",""]},"mem": {"0": ["OutputPushPull","0","16","106",false,"0034", "",""],"1": ["OutputOpenLoadDetect","0","16","108",false,"0035", "",""],"2": ["OutputPWMActive","0","16","110",false,"0036", "",""],"3": ["OutputPWMFrequency","1","8","112",false,"0037", "",""],"4": ["InputMode_1","0","8","88",false,"0055", "",""],"5": ["InputMode_2","0","8","89",false,"0056", "",""],"6": ["InputMode_3","0","8","90",false,"0057", "",""],"7": ["InputMode_4","0","8","91",false,"0058", "",""],"8": ["InputMode_5","0","8","92",false,"0059", "",""],"9": ["InputMode_6","0","8","93",false,"0060", "",""],"10": ["InputMode_7","0","8","94",false,"0061", "",""],"11": ["InputMode_8","0","8","95",false,"0062", "",""],"12": ["InputMode_9","0","8","96",false,"0063", "",""],"13": ["InputMode_10","0","8","97",false,"0064", "",""],"14": ["InputMode_11","0","8","98",false,"0065", "",""],"15": ["InputMode_12","0","8","99",false,"0066", "",""],"16": ["InputMode_13","0","8","100",false,"0067", "",""],"17": ["InputMode_14","0","8","101",false,"0068", "",""],"18": ["InputMode_15","0","8","102",false,"0069", "",""],"19": ["InputMode_16","0","8","103",false,"0070", "",""],"20": ["InputDebounce","0","16","104",false,"0071", "",""]},"extend": {}},{"GUID": "8aae26f2-b2b3-f2f1-01d2-57c04d626000","id": "device_RevPiConnectSE_20220401_1_0_001","type": "BASE","productType": "105","position": "0","name": "RevPi Connect SE","bmk": "RevPi Connect SE","inpVariant": 0,"outVariant": 0,"comment": "This is a RevPi Connect SE Device","offset": 339,"inp": {"0": ["RevPiStatus","0","8","0",true,"0000", "",""],"1": ["RevPiIOCycle","0","8","1",true,"0001", "",""],"2": ["RS485ErrorCnt","0","16","2",false,"0002", "",""],"3": ["Core_Temperature","0","8","4",false,"0003", "",""],"4": ["Core_Frequency","0","8","5",false,"0004", "",""]},"out": {"0": ["RevPiLED","0","8","6",true,"0005", "",""],"1": ["RS485ErrorLimit1","10","16","7",false,"0006", "",""],"2": ["RS485ErrorLimit2","1000","16","9",false,"0007", "",""]},"mem": {},"extend": {}}],"Connections":[]}
Any guidance on next steps to help diagnose this problem (and how to fix it :) ) are very much welcome.

Thanks in advance,
Kind regards,
Jeffrey
User avatar
nicolaiB
KUNBUS
Posts: 869
Joined: 21 Jun 2018, 10:33
Answers: 7
Location: Berlin
Contact:

Re: power led of DO module keeps flashing red

Post by nicolaiB »

You're not using our kernel and therefore this cannot work:
[ 0.000000] Linux version 6.1.28-v7l+ (dom@buildbot) (arm-linux-gnueabihf-gcc-8 (Ubuntu/Linaro 8.4.0-3ubuntu1) 8.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1651 SMP Wed May 17 14:32:54 BST 2023
Please install the revpi kernel again and do not use the raspberry pi kernel.

Nicolai
sandwave123
Posts: 4
Joined: 31 May 2023, 12:49
Answers: 0

Re: power led of DO module keeps flashing red

Post by sandwave123 »

I have tried to install a the kernel and now after i had done a reboot it won't even start up now and the screen shows only different colours
Post Reply