Hello,
our RevolutionPi Core 3 doesn't have an RTC.
See our FAQ at the following link.
RevolutionPi Hardware FAQ | Is there an external clock for the RTC in the RevolutionPi Core3 (+)?
Here is some additional information about RTC in the RevolutionPi
RTC in RevolutionPi
Search found 92 matches
- 15 Jul 2022, 11:07
- Forum: Hardware
- Topic: Revpi Core Clock Issues
- Replies: 2
- Views: 1533
- 01 Jun 2022, 11:17
- Forum: Hardware
- Topic: Ethernet drop or freezes on Revolution Pi Compact
- Replies: 6
- Views: 2260
Re: Ethernet drop or freezes on Revolution Pi Compact
Hello,
I can recommend you to follow the checklist in the link below.
https://kunbus-gmbh.atlassian.net/servi ... 2632253480
I hope that I have helped you with this
Mit freundlichen Grüßen | Best regards
Giuseppe Pagano | Technical Support
I can recommend you to follow the checklist in the link below.
https://kunbus-gmbh.atlassian.net/servi ... 2632253480
I hope that I have helped you with this
Mit freundlichen Grüßen | Best regards
Giuseppe Pagano | Technical Support
- 23 May 2022, 11:10
- Forum: Hardware
- Topic: Digital Out Pins briefly switch to HI when booting
- Replies: 12
- Views: 2665
Re: Digital Out Pins briefly switch to HI when booting
Hello all, yes, this is unfortunately a known issue. We are currently working on this bug. Unfortunately, we can't influence the behaviour. The output pins on the Compact come directly from the compute module, and we have no influence on this behaviour at boot time. Mit freundlichen Grüßen | Best re...
- 20 May 2022, 08:22
- Forum: Hardware
- Topic: Boot drive d: disappears during image writing
- Replies: 1
- Views: 823
Re: Boot drive d: disappears during image writing
Hello Walter, you can try to use an alternative to win32Diskimager, as the software sometimes causes problems when flashing. Use the software balenaEtcher instead of Win32DiskImager And if that doesn't help, you can try out if you can flash over a linux system. How to do, see in the Link below. http...
- 13 May 2022, 08:11
- Forum: Hardware
- Topic: Kurzschlussverhalten DIO
- Replies: 2
- Views: 4803
Re: Kurzschlussverhalten DIO
Hallo, ja, dies ist ein normales Verhalten des DIO-Moduls. Das DIO-Modul hat eine Erkennung, wenn ein Ausgang kurzgeschlossen ist, aber die Abschaltung betrifft dann alle Ausgänge (High-Side mode). Dies geschieht durch den Ausgangstreiber. Sie können dieses Verhalten nicht parametrieren. Es gibt abe...
- 11 May 2022, 12:57
- Forum: Hardware
- Topic: RED LIGHT OUTPUT - DO MODULE
- Replies: 4
- Views: 1598
Re: RED LIGHT OUTPUT - DO MODULE
Hello, can you check which PiCtory version you have installed on your RevPi? The latest version is 2.0.6. You can try to update the software. There are known issues with DI, DO, MIO modules with version 2.0.5. See the following link for more information about this problem and how to update. https://...
- 04 May 2022, 15:18
- Forum: Hardware
- Topic: AIO Proximity Sensor
- Replies: 1
- Views: 1833
Re: AIO Proximity Sensor
Hello Jassa, you need to check your wiring. You can wire the sensor as shown in the figure below. 4842.drawio.png I think the range of output 1 and output 2 is 0-24V. The AIO cuts off after 10V. You can connect a voltage divider with the factor 2.4 and then calculate the correct value. Mit freundlic...
- 02 May 2022, 13:48
- Forum: Hardware
- Topic: Maximum overall output current: can I assume per-port works under full load?
- Replies: 4
- Views: 1642
Re: Maximum overall output current: can I assume per-port works under full load?
Hello Kees,
all 14 output ports can supply 500mA simultaneously, in highside mode.
If the module gets too warm, all ports are switched off. This prevents the device from being damaged.
Best regards
Giuseppe Pagano | Technical Support
all 14 output ports can supply 500mA simultaneously, in highside mode.
If the module gets too warm, all ports are switched off. This prevents the device from being damaged.
Best regards
Giuseppe Pagano | Technical Support
- 29 Apr 2022, 09:10
- Forum: CODESYS
- Topic: RevPi Connect+ feat. CODESYS + PROFINET (Master)
- Replies: 1
- Views: 3064
Re: RevPi Connect+ feat. CODESYS + PROFINET (Master)
Hello Aleksandr, you don't need another licence for Profinet. Did you flash a new image before this problem with the licence appeared? If you have a Codesys licence and want to flash a new image onto the RevPi, you must first create a backup of your licence. The following link describes how to back ...
- 25 Apr 2022, 09:02
- Forum: Software
- Topic: imagebakery step by step
- Replies: 4
- Views: 1450
Re: imagebakery step by step
Hello Rivas, Take a look at our FAQ page, which you can reach via the link below. https://kunbus-gmbh.atlassian.net/servicedesk/customer/portal/1/article/1058439239 | "Is it possible to reduce the memory size of the image because the 4GB eMMC is almost exhausted with the standard image?" T...